وظائف فني أجهزة إنذار الحريق في مصر

<h2><span lang="en" dir="ltr">State Lawsuits Authority announcement for a Technician position</span></h2><h3><span lang="en" dir="ltr">Job Description</span></h3><h4><span lang="en" dir="ltr">Purpose of the job:</span></h4><ul><li><span lang="en" dir="ltr">The incumbent handles technical tasks that require experience in conducting them and knowledge of how to perform them.</span></li><li><span lang="en" dir="ltr">The job holder performs their duties in accordance with laws and regulations.</span></li></ul><h4><span lang="en" dir="ltr">Key Tasks:</span></h4><ol><li><span lang="en" dir="ltr">Completing assigned work and duties as specified.</span></li><li><span lang="en" dir="ltr">Performing other assigned tasks.</span></li></ol><h4><span lang="en" dir="ltr">Maximum age at the time of application:</span></h4><p><span lang="en" dir="ltr">45 years</span></p><h3><span lang="en" dir="ltr">Application Details</span></h3><p><span lang="en" dir="ltr"><strong>Application deadline:</strong></span></p><p><span lang="en" dir="ltr">2026/10/05</span></p><h4><span lang="en" dir="ltr">Required Documents:</span></h4><ol><li><span lang="en" dir="ltr">Original approval from the employer for secondment (with financial grade), transfer, or loan.</span></li><li><span lang="en" dir="ltr">A job status statement indicating the job title, grade, and occupational group held, provided it is a permanent position.</span></li><li><span lang="en" dir="ltr">The last efficiency report for the last two years, with a rating of no less than (Excellent) for each.</span></li><li><span lang="en" dir="ltr">An official, stamped, and certified statement showing penalties imposed and their reasons, and what has been cleared and the reasons for clearance, in addition to a copy of judicial rulings, if any.</span></li><li><span lang="en" dir="ltr">An official, certified, and stamped statement of special and sick leaves.</span></li></ol><p><span lang="en" dir="ltr">The above documents must bear the Republic's emblem seal.</span></p><h4><span lang="en" dir="ltr">Place of application:</span></h4><p><span lang="en" dir="ltr">Applications for these positions are submitted by accessing the State Lawsuits Authority website at (</span><a href="https://sla.gov.eg"><span lang="en" dir="ltr">https://sla.gov.eg</span></a><span lang="en" dir="ltr">) during the period from the application start date to the application end date and following the steps on the website.</span></p><h3><span lang="en" dir="ltr">Job Requirements</span></h3><h4><span lang="en" dir="ltr">Qualification Requirements:</span></h4><p><span lang="en" dir="ltr">Appropriate qualification between higher, intermediate, or lower than intermediate.</span></p>

Job title: Electrical Control Technician. Department: Maintenance – Electrical Maintenance. Direct supervisor: Electrical Maintenance Supervisor / Electrical Maintenance Engineer. Location: 10th of Ramadan City - Sharkia<br> About the company<br>Alama for Automotive Plastics (Auto Plast) is a manufacturing company specialized in producing boxes, panels and corrugated plastic spacers, in addition to custom-designed packaging solutions. The company also trades in products related to electrostatic discharge protection and car battery components. With its excellent services to prominent customers in electronics, automotive, and signage sectors, Alama has established its position as a trusted partner. The company is committed to providing high-quality solutions tailored to meet diverse customer needs.<br>Job responsibilities: Ensure stable and safe operation of electrical control systems in machines and production lines through preventive and corrective maintenance, diagnose electrical and electronic faults in industrial control systems, and maintain efficiency of control panels and instrumentation to ensure continuous production, minimize downtime and achieve the highest level of equipment operational reliability.<br><br> Role scope: The scope includes handling components of Industrial Control Systems, including: electrical power circuits, industrial control circuits, PLC, industrial sensing and measuring instruments, motor control systems, speed control systems for electric motors, electrical protection systems.<br>Detailed tasks and responsibilities: First: Operating and maintaining industrial control systems - Install and maintain electrical control circuits for industrial machines and production lines. Inspect and operate electrical control panels and verify components. Monitor efficiency of control systems associated with production equipment. Adjust operating system settings to meet industrial operation requirements. Ensure operation of sequential control systems inside machines.<br>Second: Analyze and diagnose electrical faults - Analyze electrical faults in machines using systematic fault diagnosis methodology. Determine root causes of electrical and electronic faults. Inspect power and control circuits to identify failure points. Use electrical measuring devices to pinpoint faults. Implement necessary repairs and retest systems after maintenance.<br>Third: Maintenance of industrial control panels - Perform periodic maintenance of electrical control panels within the plant. Inspect main components such as: circuit breakers, contactors, electrical relays, power supplies. Ensure tight electrical connections and prevent overheating inside panels. Clean panels of dust and moisture. Check insulation levels.<br>Fourth: Handling industrial electrical motors - Operate and maintain motors used in production lines. Inspect motor start-up systems. Ensure motor protection systems are efficient. Analyze electrical faults related to motors. Adjust motor operating settings to suit loads.<br>Fifth: Operating and maintaining speed control systems - Operate and adjust motor speed control devices (VFD / Inverter). Read and analyze fault codes for speed control units. Set operating parameters such as acceleration, deceleration, current limits. Ensure compatibility of speed control systems with operation requirements.<br>Sixth: Maintenance of industrial sensing and measuring devices - Inspect and maintain industrial sensors used in production lines. Calibrate sensor positions to ensure accurate operation. Test efficiency of industrial measuring devices. Replace faulty or inaccurate sensors. Ensure control signals from sensors to control systems are intact.<br>Seventh: Handling programmed logic control systems - Monitor input/output signals of programmable logic controllers. Analyze operational problems related to control software. Check wiring of PLC control systems. Assist in testing control programs after modification or maintenance. Support automation engineers in system operation processes.<br>Eighth: Implement preventive maintenance - Execute approved preventive maintenance programs for electrical equipment. Prepare periodic maintenance reports. Record faults and repairs performed. Monitor recurring fault indicators. Contribute to improving equipment reliability.<br>Ninth: Compliance with industrial safety requirements - Adhere to electrical safety procedures inside the plant. Implement energy isolation procedures before maintenance. Use personal protective equipment during work. Report any electrical or operational hazards. Comply with occupational safety and health standards.<br>Scientific knowledge required: The candidate should have strong knowledge of basic scientific concepts in the fields of: fundamentals of industrial electricity.<br><br>Technical skills required: Basic technical skills - Read industrial electrical diagrams. Analyze electrical control circuits. Use electrical measuring devices. Install and maintain control panels. Work with industrial electrical motors. Basic maintenance of electronic circuits.<br>Advanced technical skills - Analyze faults in industrial control systems. Work with PLC industrial systems. Set speed control systems for motors. Maintain industrial sensors. Understand industrial control logic. Know the basic components of electronic control units.<br>Behavioral skills - Analytical thinking. Problem-solving ability. Quick fault response. Work in a maintenance team. Adherence to safety procedures.<br>Qualifications required - Diploma in Industrial Technician specializing in electricity or a technical institute diploma in electricity. Experience required - Practical experience of 3 to 5 years in maintenance of industrial electrical systems. Experience in plastic production factories is preferred. and the rest<br>If you are interested in joining our team and building your career in plastic manufacturing, please send your CV to the email rec@autoplastegypt.com with the job title mentioned in the subject line,<br>or contact the HR officer by phone at: 01023483222.

job description Help Desk Technician is needed to be hired at our Asyut Branches Min. 2 years of experience in the same position Bachelor of MIS or any relevant degree is a must Good understanding of computer systems, mobile devices, and other tech products Ability to diagnose and troubleshoot basic technical issues Familiarity with remote desktop applications and help desk software Excellent problem-solving and communication skills* Monitor network performance and optimize the network of optimal speed and availability* Multi-tasking with excellent time management skills and ability to work under pressure.<br>Job Description:<br>Provide hardware, software and all front-end technical support for internal users. Troubleshoot and resolve hardware and software application issues Set up new desktops and laptops with necessary business applications. Installing and configuring computer hardware, software, systems, networks, printers and scanners. Set up user accounts, permissions, mailboxes, groups, Users applications . Configure and troubleshoot hardware as necessary (computers, printers, mobile phones, networking, wiring, etc.). Perform routine and preventative maintenance on printers, scanners and other equipment. Testing new technology and organizing cables and testing the passive network Install, maintenance and testing security cams

<p>&nbsp;We are seeking a Technical Office Engineer/Engineer for a furniture and home furnishing factory<br>The location: Belbeis<br>Required software<br>3D Max - SketchUp - AutoCAD<br>Working hours from 8:30 AM to 5:00 PM<br>Leave: Friday + annual leaves and official holidays<br>Social security .. company-paid transportation available<br>Daily meals provided at company expense<br>The salary is attractive and will be determined after the interview<br>Preference for residents of Zagazig or Belbeis and surrounding areas</p>